# AFAD Traffic Control: Plan the Devices, Flagger Positions and Lane Closure

**Author:** Julio Martinez Sr.

**Published:** November 21, 2026  

**Last updated:** November 21, 2026  

**Category:** Construction Management

**URL:** https://draftech.com/blog/afad-traffic-control

**Title tag:** AFAD Traffic Control: Device Types and Plan Rules 2026

**Meta description:** AFAD traffic control guide: STOP/SLOW and red/yellow devices, trained flaggers, MUTCD rules, plan locations, sight distance and state DOT approval checks.

**Primary keyword:** afad traffic control

**Plan reference:** plan-2026-10-22

**Visible word count:** 3122

**Read time:** 12 min read

![A gray sedan stops at a red-lit trailer gate arm on a wooded road as a vested worker holds a handheld device.](/blog/img_afad_traffic_control.webp)

## In this article

- [AFAD Traffic Control Still Requires a Flagger](#meaning)
- [Choose Between the Two AFAD Types](#types)
- [What an AFAD Traffic Control Plan Must Show](#plan)
- [Confirm State DOT Limits and Project Approval](#approval)
- [Check the Operating Arrangement Before Traffic Enters](#field)
- [Choose the Next Step for Your Route](#decision)

An automated flagger assistance device (AFAD) is a remotely operated STOP/SLOW sign or red and yellow lens unit that lets a flagger control one-lane, two-way traffic from outside the lane. The operator still decides when vehicles can proceed. For a utility route, we start with whether that operator can see and control the proposed work zone.


A fiber trench or a power-distribution work area can take one lane while traffic alternates through the other. Wireless access work can create the same arrangement. We approach the AFAD decision through the traffic-control plan: establish the operating method, place the equipment against measured road conditions and confirm the road authority accepts the arrangement before construction uses it.



## AFAD Traffic Control Still Requires a Flagger


With afad traffic control, an automated flagger assistance device controls alternating traffic through a work zone while its trained flagger operates outside the lane. MUTCD Part 6 recognizes 2 types: remotely controlled STOP/SLOW signs and red/yellow lens devices with gate arms. The device assists the flagger; it does not make the traffic-release decision independently.


The current federal publication is the **11th Edition of the MUTCD with Revision 1, December 2025**, as identified by FHWA. Part 6 places general AFAD provisions in Section 6L.02, followed by the two device-specific sections. We put that edition and the applicable state adoption or supplement on the design basis so a reviewer can identify which requirements the drawings follow.


Section 6L.02 states: **“AFADs shall only be used in situations where there is only one lane of approaching traffic in the direction to be controlled.”** That restriction makes the approach lane count part of our initial review: a turn lane or an additional through lane changes the problem, even when construction occupies only a small part of the roadway beyond it.


The same section requires an operator trained on the AFAD and prohibits leaving it unattended during use. Two flaggers are the baseline for either permitted arrangement: an AFAD at each end, or an AFAD at one end with a flagger at the other. For the single-flagger option, the operator must have unobstructed views of both the devices and approaching traffic in both directions; seeing the units alone does not satisfy those conditions.


A limitation of our recommended AFAD approach is its dependence on unobstructed operator views, regardless of remote-control range. A radio connection can remain available when a crest or a parked construction vehicle blocks approaching traffic from view, so the drawing needs to identify where the operator will stand. If a single operator cannot meet the visibility conditions, the plan needs a different arrangement rather than a note promising extra attention.


Section 6L.02 identifies short-term and intermediate-term activities as appropriate uses for AFADs, while its guidance discourages long-term stationary use. They cannot replace a continuously operating temporary traffic-control signal. We evaluate that distinction when a utility excavation remains between work shifts, since an unattended closure needs its own accepted traffic-control arrangement instead of equipment left in flagging mode.


Flagger basics still include the applicable training, high-visibility apparel, clear communication and a safe station, addressed in our [work-zone traffic-control planning guide](/blog/work-zone-traffic-control-plan-telecom). Although the remote handset changes how the indication is displayed, the operator remains responsible for watching traffic and confirming that the shared lane has cleared.



## Choose Between the Two AFAD Types



### STOP/SLOW units use a changing sign face


A STOP/SLOW AFAD presents the familiar alternating sign faces on a trailer or movable cart. MUTCD Section 6L.03 specifies a rigid, retroreflective sign at least 24 by 24 inches, with letters at least 8 inches high and the bottom of the sign at least 6 feet above pavement. The equipment submittal should also identify the active conspicuity devices that supplement the sign, so those features can be reviewed with the rest of the proposed configuration.


The WAIT ON STOP sign tells drivers how to respond while they face the unit. A GO ON SLOW message is an option under the federal provisions. The federal guidance recommends a gate arm for this type; the red/yellow type requires one. We keep that distinction in the equipment schedule so the two types cannot be substituted without reviewing their different requirements.


Only after oncoming vehicles have cleared the one-lane portion does the displayed SLOW face authorize the next movement. Safeguards must prevent opposing SLOW displays at the same time. In our plan notes, the release procedure accounts for the actual work-zone length and for vehicles entering from access points between the end stations, so clearance means more than watching the original queue pass.



### Red/yellow lens units use a required gate arm


A red/yellow AFAD combines a steady red indication for stopping with a flashing yellow indication for proceeding cautiously. MUTCD Section 6L.04 requires 12-inch lenses and a gate arm coordinated with those indications. There is no green phase. A STOP HERE ON RED sign identifies the stopping point, which the designer must relate to the unit and approaching traffic.


The gate lowers with the steady red display and rises for the flashing yellow display. The change back to red includes a steady yellow interval under Section 6L.04. We leave the equipment's required indication sequence explicit in the operating documentation rather than describing it as an ordinary portable traffic signal, which follows a different control framework.


A photograph or catalog description may leave out a sign attachment or visibility feature required by the project specifications. Those omissions can change the equipment footprint, which is why we settle the agency's accepted configuration before finalizing the shoulder space reserved for either type. The equipment review and the layout need to describe the same installation.



## What an AFAD Traffic Control Plan Must Show


The drawing needs enough information to test the operation against the road. We use the following checks to connect the AFAD arrangement to the work area; the table identifies design questions, not universal dimensions or a replacement for the governing agency's standard sheets.


<table class="comparison-table"><thead><tr><th>Plan element</th><th>Show on the drawing</th><th>Resolve before release</th></tr></thead><tbody>
<tr><td>Unit locations</td><td>Each device, stop point and footprint</td><td>Usable shoulder and gate clearance</td></tr>
<tr><td>Advance warning</td><td>Sign sequence and approach distances</td><td>Visibility before the back of the queue</td></tr>
<tr><td>Taper</td><td>Transition geometry and channelizing devices</td><td>Vehicle path beside the actual work envelope</td></tr>
<tr><td>Flagger position</td><td>Operator stations and communication method</td><td>Views required by the selected staffing arrangement</td></tr>
<tr><td>Sight distance</td><td>Approach checks and controlling obstructions</td><td>Stopping visibility and operator sight lines</td></tr>
</tbody></table>

### Locate the units against the work envelope


An AFAD symbol should represent a usable installation location. We want its footprint shown beside the intended stop point, with the gate's operating space checked against the traveled lane. The federal guidance places AFADs before the one-lane, two-way taper and beyond the point where approaching traffic stops. A unit cannot simply occupy whichever shoulder space remains after construction equipment arrives.


The construction occupation needs its own outline on the drawing because a trench line alone understates the space needed for spoil beside the excavation or a service truck stopped next to the opening. For aerial work, evaluate the working vehicle's setup and the access needed to reposition it, because moving that vehicle can change both the traffic path and the operator's view.



### Make advance warning useful to approaching drivers


For advance warning on the approach, Section 6L.02 recommends ROAD WORK AHEAD and ONE LANE ROAD signs, followed by BE PREPARED TO STOP. Each location belongs on the drawing so the installer can follow the planned warning sequence instead of reconstructing it from a device count. A driver reaching the rear of a queue needs warning before that point, not just a clear view of the stopped car ahead.


A curve on one side and an open tangent on the other can make a mirrored drawing misleading. Our approach checks therefore treat each direction separately, including queues that could grow beyond the operator's view. The drawing should identify where the crew can assess queue growth and what condition requires the responsible traffic-control lead to change the setup.



### Keep the taper connected to the usable lane


Taper and sign spacing must follow the applicable road conditions and agency criteria, as explained in our [MOT plan guide for fiber construction](/blog/mot-plan-fiber-optic-construction). We identify the taper type before selecting its dimensions. A one-lane, two-way transition serves a different movement from a multilane merging taper, so a familiar formula cannot be applied just because it appears on another drawing.


To establish whether the open lane remains usable, we trace the expected vehicles through the transition and past the work. A shoulder edge or construction access may force their path toward the excavation even when the lane looks wide enough on the drawing. We also check how the lane reopens at the far end. That departure geometry affects whether a released queue can clear without hesitation.



### Give the flagger a workable station


The plan needs to locate the operator outside the lane at a station with the views required for the proposed method. A label reading “remote operator” cannot establish visibility when the field crew has to choose between standing behind a work vehicle and standing beside a ditch, neither of which was evaluated in the design.


Our operating notes assign responsibility for communication and fallback arrangements to the party providing traffic control. A loss of communication must have a defined response before vehicles are released from either end. The plan should make clear who verifies that the shared lane is clear and how that confirmation reaches the opposite station.



### Check sight distance from the road


**Driver stopping visibility and operator visibility are separate checks.** One concerns the approaching driver's ability to recognize the stop condition and respond; the other concerns what the flagger can see while controlling the devices. We record the controlling obstruction for each approach, because a clear aerial image cannot establish either view beneath vegetation or over a vertical crest.


Nighttime work adds another condition to the visibility review. Section 6L.02 requires illumination of the AFAD location when used at night, and our design needs to account for glare as well as the operator's view. A layout evaluated in daylight still needs that lighting review before it can support the intended nighttime operation.


Construction vehicles can also obscure sight lines that were clear during the survey. Before accepting the remote operator's station, we compare those views with the equipment in working position: an empty shoulder can make a layout appear workable while the actual setup blocks the view that justified the staffing plan.


Our [Traffic Control Plan Template](/tools/traffic-control-plan-template) is a free 3-page fillable download behind a short form that organizes a plan without prescribing spacing, taper or speed values. It provides a place to collect the design information, while the responsible designer establishes those values from the road conditions and applicable requirements.



## Confirm State DOT Limits and Project Approval


Federal recognition of 2 AFAD types does not establish that every configuration is accepted on every road. Because state requirements can be tighter, our equipment review starts with the road owner's adopted manual and specifications. That review also identifies whether the particular work-zone arrangement needs project approval or must follow a prescribed standard sheet.


Minnesota DOT's Temporary Traffic Control Electronic Equipment approved-products page distinguishes a listed product from a configuration that satisfies its requirements. Its AFAD qualification criteria require STOP/SLOW signs at least 36 by 36 inches with letters at least 12 inches high. That is a specific state example, not a nationwide dimension. For our equipment review, the applicable state's requirement determines which sign configuration belongs in the submittal.


The distinction matters during procurement. A product family appearing on a list does not establish that every available attachment or option meets the project requirement, so the submitted configuration should match the one the contractor intends to bring to the road. We ask for evidence of that configuration during review so differences can be resolved before they become field substitutions.


New York State DOT's May 2026 Standard Sheets, Book 3, show a red/yellow AFAD application and require appropriate flagger tools ready for a malfunction or traffic volumes beyond the device's effective control. We cite this as an example of a state operating requirement. It should not be copied into another state's plan as if the federal manual prescribed that state's entire setup.


Lane-closure permits establish the road authority's conditions for occupying the lane, a separate coordination task covered in our [state DOT lane-closure permit guide](/blog/state-dot-lane-closure-permit-fiber). An equipment acceptance record answers a different question. We keep the closure authorization tied to the approved drawing revision so the field team can identify which layout the agency accepted.


For a route with moving work fronts, our [fiber construction management](/services/fiber-construction-management) scope connects the approved construction sequence to field execution. As that sequence advances, a device location accepted for one work area needs reassessment if the next excavation changes the shared-lane length or introduces a driveway inside the controlled section.



## Check the Operating Arrangement Before Traffic Enters


At setup, the accepted plan gives the field team a basis for comparing the unit type and signs with the equipment present. The traffic-control provider also needs to demonstrate the intended operation, including the safeguards that prevent both ends from releasing opposing traffic into the shared lane at the same time. We want those checks completed before the equipment is relied on to control traffic.


A walk through the proposed stop points before the closure starts lets the field team check the operator's view from the assigned station with construction vehicles in place. During that confirmation, the lane must remain closed to conflicting releases. The qualified traffic-control personnel must understand the recovery procedure for a failed indication or lost control connection.


Between the stations, a driveway can introduce a vehicle after the flagger has watched the main queue pass. The operating plan needs a way to account for that movement before the opposing direction receives permission to proceed. We would not assume the last vehicle past the entry unit is always the last vehicle inside the closure.


Even after a correct morning setup, a delivery truck can block a sign. Assigning unrelated construction duties to the operator can also divide attention when traffic needs active control. In our operating notes, the AFAD operator's role stays explicit, and the traffic-control lead is responsible for correcting changed conditions throughout the work.


At shutdown, Section 6L.02 requires removal or covering of the AFAD's associated signs when the device is not being used. If the excavation remains, the remaining closure needs an accepted method of control. Removing a flagging message does not by itself establish how traffic will pass the unfinished work.



## Choose the Next Step for Your Route


**For route designers:** resolve the footprint while the work area can still move. Our designers establish the lane arrangement and sight lines before specifying an AFAD, allowing room to relocate a station around curves or shoulder restrictions.


**For permit coordinators:** use that layout to confirm the road owner's AFAD policy and equipment acceptance requirements. We keep the owner's answer with the plan revision so the reviewer can evaluate the intended operation from the application, without having to reconstruct it from a generic equipment brochure.


**For construction leads:** confirm that the planned station remains usable after equipment is set. Agreement with the traffic-control provider on the fallback belongs before the first release, when a blocked view can still be corrected without opposing queues committed to the closure. If conditions have changed, the crew needs to stop and resolve them before proceeding.


**[Discuss the traffic-control plan for your route](/#dt-contact).** Bring the work limits and proposed lane occupation so we can identify the design questions that need to be resolved with the road authority.


Draftech International delivers turnkey telecom and power infrastructure with engineering 100% in-house and construction delivered by Draftech-managed crews under Draftech's QA/QC. For the road-occupation problems described here, our traffic-control scope covers MOT plan design, flagger positioning, signage and channelization design, and lane-closure permit coordination. Send the proposed work limits through our [contact page](/contact) or email [info@draftech.com](mailto:info@draftech.com) so we can discuss the planning scope.


If the route is still taking shape, the [qualifying-route engineering offer](/free-design) lets you bring those road constraints into the design discussion: Draftech engineers the first 20,000 linear feet at no cost, from feasibility and field survey through permit approval. The owner reviews each request before Draftech commits the package.

## Frequently Asked Questions

### Does an AFAD eliminate the flagger?

No. MUTCD Part 6 requires a flagger trained to operate the device and prohibits leaving it unattended during use. We treat the AFAD as a way to move the operator outside the traffic lane while preserving active control, and we check the proposed staffing arrangement against the visibility conditions before including it in the traffic-control plan.

### Can one flagger control two AFADs?

The federal option allows 1 flagger to control two AFADs only with unobstructed views of the devices and approaching traffic in both directions. Both views need checking from the proposed station; radio range alone tells us too little about visibility. Before that staffing assumption enters the approved plan, we also confirm that the road authority accepts the arrangement under its own policy.

### What is the difference between the two AFAD types?

The 2 federally recognized types use either a changing STOP/SLOW sign face or red/yellow lenses with a required gate arm. We distinguish them on the equipment schedule because their displays and associated signs differ, and a state can impose additional configuration requirements that prevent a contractor from treating the units as interchangeable equipment for an approved closure.

### Can an AFAD operate overnight without an attendant?

No. Section 6L.02 prohibits leaving an operating AFAD unattended and requires illumination at its location when used at night. If the work leaves a lane closed between shifts, we address that traffic arrangement during design. A device intended for attended flagging cannot simply be left running as a substitute for a continuously operating temporary traffic-control signal.

### Does a traffic-control template determine AFAD spacing?

No. Our free 3-page Traffic Control Plan Template organizes plan information without prescribing spacing, taper or speed values. We use the actual approach conditions and applicable agency requirements to establish the layout, including the unit locations and operator station; filling out a template does not by itself establish that the proposed work zone can be safely operated.
